My Binding Challenge Spartan 150M Manual de instrucciones

Instruction Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com CHALLENGE SPARTAN 150SA PAPER CUTTER

5.0 Installation & Setup 9 5.0 Installation & Setup 5.1 Inspecting Shipment This machine has been carefully packed to prevent damage d

5.0 Installation & Setup 10 5.4 Power Hook-Up SHOCK HAZARD! NEVER CUT THE GROUND TERMINAL from a three-prong plug to fit a two-prong socket.

6.0 Operation 11 6.0 Operation IMPORTANT: DO NOT ATTEMPT TO OPERATE THE CUTTER UNTIL YOU HAVE THOROUGHLY READ AND UNDERSTAND ALL OF THE FO

6.0 Operation 12 If the knife is not at the “up” postion when the main power switch is turned on, the knife will automatically move to the “up” p

6.0 Operation 13 6.3 Jogging Aid Always remove the jogging aid from the table before making a cut. A jogging aid is included as standard eq

6.0 Operation 14 Figure 11 – Line Light 6.5 Making a Cut Open the front shield and set the backgauge to the desired position. Place the paper sq

6.0 Operation 15 6.7 Operating Tips • Correct clamping pressure is important for getting good results. Insufficient clamping pressure may re

7.0 Knife Installation/Changing 16 7.0 Knife Installation/Changing Changing knives can be very dangerous unless safety precautions are observed

7.0 Knife Installation/Changing 17 3. Remove the two knife bolts from the slotted knife bar holes ONLY and replace with the knife lifter asse

7.0 Knife Installation/Changing 18 Figure 15 5. Insert and tighten four knife bolts. 6. Remove the knife lifter assembly and replace with the

F.150-O Dec. 2004 SPARTAN 150 SA SEMI-AUTOMATIC PAPER CUTTER Sold and Serviced by

7.0 Knife Installation/Changing 19 A knife can last between 2,000 and 5,000 cuts before it needs to be sharpened. Cutting soft paper (such a

7.0 Knife Installation/Changing 20 • If a knife bolt is damaged, replace it. • Always keep knife bolts securely tightened. • Store knives in

7.0 Knife Installation/Changing 21 NOTES

8.0 Maintenance and Troubleshooting 22 8.0 Maintenance and Troubleshooting 8.1 Maintenance All maintenance on this machine should be performed by

9.0 Footprint 23 9.0 Footprint

10.0 Safety Systems Test 24 10.0 Safety Systems Test Machine manufacturer CHALLENGE Model SPARTAN 150 SA Se

10.0 Safety Systems Test 25 Please enter date and initials for both tests. Date ______ ______ ______ ______ ______ ______ ______ ______ ___

1.0 Introduction 2 1.0 Introduction THIS MANUAL is designed to help you get the most from your Challenge equipment. Keep this manual in a safe, c

1.0 Introduction 3 TABLE OF CONTENTS 1.0 Introduction...

2.0 Safety 4 2.0 Safety 2.1 Precautions • This machine is designed for one-person operation. Never operate the machine with more than one person

2.0 Safety 5 2.3 Warning Label Definitions The following warning labels are found at various locations on your machine. Read and understand t

2.0 Safety 6 !OJO! This Este simbolo de alerta de seguridad significa ¡ OJO ! - INSTRUCCIONES DE SEGURIDADPERSONAL. Lea las instrucciones porq

3.0 Packing List 7 3.0 Packing List Part No. Description Qty.Spartan 150 SA 15” Semi Automatic Paper Cutter 1 5064 Cutting Stick Puller

4.0 Specifications 8 4.0 Specifications Description Inch Units Metric Units Cutting Width 15-3/4” 40 cm Minimum Cut 1-15/16” 4.9 cm Clamp